Installing Zimbra on VServer
Installation on VServer
These instructions are specifically for Debian VServers, but should be able to be applied to just about any system
WARNING - Upgrading Zimbra will overwrite all of these files - you must patch them after installing and each upgrade.
Debian and VServers
Remember when running a linux-vserver.org Vserver that the host machine will be arping for all the IPs in the Vservers. It will also accept any connections in its tcp stack for any IP in a vserver if the TCP stack has a deamon bound to *:port - ie postfix listening on *:25 on the vserver host will interfere with postfix on 220.127.116.11:25 on the vserver. Make sure you have bound ALL daemon ports (smtp, ssmpt, imap2, imap3, imaps, etc etc) to specific Ips on the host. How to do this is beyond the scope of this page, but generally check config files (/etc/postfix/conf/main.cf, /etc/dovecot.conf, /etc/apache/httpd.conf, etc) for Listen or Interface or other equivalent statements. When in doubt, RTFM.
A base Debian vserver doesn't have a "file" utility installed by default. This is needed by amavis. The installer will fail, if getopt isn't installed, for this you need "libgetopt-mixed-perl". Apache and Tomcat will fail, as the base vserver doesn't have "libexpat1" installed. Install it by typing:
apt-get install file libexpat1 libgetopt-mixed-perl
Matter of fact, all packages required for installing Zimbra are:
apt-get install libgetopt-mixed-perl file libc6-i686 sudo libidn11 curl fetchmail libgmp3 \ libxml2 libstdc++6 openssl libexpat1 libpcre3
Note: As of etch, libgmp3 isnt available anymore, libgmp3c2 or 4xx is required instead. Not finished testing install with 3c2 to see if it works. --mathx
Make sure you have a localhost entry and also an entry with your primary IP. For example:
127.0.0.1 localhost.localdomain localhost 18.104.22.168 mail.somehost.zimbra mail
The Zimbra logger process doesn't seem to startup. "zmcontrol status" on my system shows:
vserver:~# /opt/zimbra/bin/zmcontrol status Host vserver.somedomain antispam Stopped antivirus Stopped ldap Running logger Stopped mailbox Stopped mta Stopped snmp Stopped spell Running vserver:~#
The logger uses MySQL. I'm guessing there is some problem with privileges and/or connecting to localhost in the "mysql" database. Just a hunch though.
I installed Zimbra on a new VServer and the logger seemd to startup properly. "zmcontrol status" shows it running after several stops/starts. However, I'm still not getting any log data. All statistics windows say "Data not available yet.". Oh well.
major issue with Zimbra 4.5 The postfix main.cf config is auto generated before postfix is run, so any changes you make to postfix/conf/main.cf will be overwritten. The problem with this is that the content filter is reset to be amavis 127.0.0.1:1024, which obviously won't work. Trying to figure out where the master config for postfix is generated right now. Please update if you find out. Mathx 09:25, 12 October 2007 (PDT)
22.214.171.124:10025 inet n - n - - smtpd -o mynetworks=127.0.0.1/8,126.96.36.199
Where 188.8.131.52 is your real IP number (not 127.0.0.1). Do not forget to change the mynetworks line as well, or your AV will not be able to connect back to postfix on 10025 for final delivery.
Note: It may not be a good idea to use a real internet IP here, your RFC1918 picked replacement IP for 127.0.0.1 is a better idea. I dont know that it's a good thing to have port 10025 open to the internets.
content_filter = smtp-amavis:[184.108.40.206]:10024
Recently you also have to change zmmta.conf in /opt/zimbra/conf
POSTCONF content_filter smtp-amavis:[220.127.116.11]:10024
or your changes will keep getting overwritten.
Security limits (SuSE OSS 10.0 vserver)
Edit /etc/security/limits.conf and comment the last two lines - otherwise the su command won't work and the installation will fail.
# End of file #zimbra soft nofile 10000 #zimbra hard nofile 10000
Rerun /opt/zimbra/libexec/zmsetup.pl to complete the setup.
Edit /opt/zimbra/amavisd/sbin/amavisd (main Perl script) and explicitly add the IP address of the Zimbra VServer to the "inet_acl" line. I.e:
@inet_acl = qw( 127.0.0.1 18.104.22.168 [::1] ); # allow SMTP access only from localhost
Postfix should then be able to talk to Amavis...
You may also need to change BIND address and the two services back to postfix (10025 port). Basically look for 127.0.0.1. (?? This line is overly vague, refine please --mathx)
Additional changes likely required in /opt/zimbra/amavisd/sbin/amavisd (perl script):change
$inet_socket_bind = '127.0.0.1'; # limit socket bind to loopback interfaceto
$inet_socket_bind = '10.11.12.5'; # no loopback in vserver, use rfc1918 internal ip bound to your vserver
also few lines down:
$notify_method = 'smtp:[127.0.0.1]:10025'; # change these to also match your internal $forward_method = 'smtp:[127.0.0.1]:10025'; # rfc 1918 ip addr (can use inet ip, but not recommended)
A bunch of filters in /opt/zimbra/conf/amavisd.conf also need updating from 127.0.0.1:(port) to whatever IP you are using (though many in the default file are commented out, I think I found 3 in the default zimbra amavisd install that needed changing.)
Additionally the local MX for /opt/zimbra/conf/dspam.conf needs changing as well.
Vserver /tmp size
My install of Zimbra wouldn't start clamd with my default debian 16m of /tmp ramdisk space in my vserver. I had to edit /etc/vservers/(name)/fstab and increase it to 128m (though smaller may work, I didnt test), and restart the vserver. 128m lets it start anyway, not sure if I'll run out during operations. --mathx
Tomcat/Java Memory Usage
While trying to get tomcat to start on our Vserver, we kept getting this error in catalina.out:
Invalid initial heap size: -Xms8001m The specified size exceeds the maximum representable size. Could not create the Java virtual machine.
By default, tomcat will use 50% of the system memory available (as defined in tomcat_java_heap_memory_percent). On our 16Gb machine, Tomcat tried to use 8Gb and failed. You can override this default by issuing:
zmlocalconfig -e tomcat_java_heap_memory_percent="6"
Where the 6 means 6% (983.04Mb in our case).