Enabling Zimbra Proxy
From Zimbra :: Wiki
|This article applies to the following ZCS versions.|
Recommended Way To Deploy Proxy In Existing Non-Proxy Environments
Using new servers
Here you are installing the proxy on a brand new server and having all your existing mailbox servers being accessed through the proxy on this new server. Simply use the installer script (install.sh) and select the proxy and memcached packages ('Y' by default with ZCS 8.5+, just need to hit enter). This will ask you for LDAP hostname/password, Bind password for nginx ldap user which you need to provide (do 'zmlocalconfig -s ldap_nginx_password' on the host running ldap to get this) and then the Proxy configuration menu would be displayed which would look like this.
1) Status: Enabled 2) Enable POP/IMAP Proxy: TRUE 3) IMAP server port: 7143 4) IMAP server SSL port: 7993 5) IMAP proxy port: 143 6) IMAP SSL proxy port: 993 7) POP server port: 7110 8) POP server SSL port: 7995 9) POP proxy port: 110 10) POP SSL proxy port: 995 11) Bind password for nginx ldap user: set 12) Enable HTTP[S] Proxy: TRUE 13) Web server HTTP port: 8080 14) Web server HTTPS port: 8443 15) HTTP proxy port: 80 16) HTTPS proxy port: 443 17) Proxy server mode: https
If you need to change any of these intentionally, you can do that now by selecting the corresponding config item from the menu (say for eg. to disable POP/IMAP proxy, select '2' from the above menu). Otherwise, just proceed with all the defaults and you would have the proxy+memcached installed on this new server. Now, to have all the mailbox servers use the proxy, simply set the zimbraMailReferMode to reverse-proxied on each mailbox server and restart mailboxd to have all the traffic go through the proxy.
Using existing servers
Assuming you are running a 8.0 or earlier version ZCS with no proxy/memcached, zimbraMailMode as https and now want to upgrade to 8.5+ along with adding proxy & memcached, you need to follow the following steps
Start 8.5+ installer (install.sh script)
Do you wish to upgrade? [Y] y
Install zimbra-memcached [N] y
Install zimbra-proxy [N] y
After install is done, enable web/mail proxy, and set the proxy mode and ports:
- If localconfig key 'zimbra_require_interprocess_security' is set, Only "https" and "both" are valid modes
./libexec/zmproxyconfig -e -w -o -a 8080:80:8443:443 -x <https/both> -H `zmhostname`
- Else if 'zimbra_require_interprocess_security' is unset, Only "http" and "both" are valid modes
./libexec/zmproxyconfig -e -w -o -a 8080:80:8443:443 -x <http/both> -H `zmhostname`
- Set the mail proxy ports
./libexec/zmproxyconfig -e -m -o -i 7143:143:7993:993 -p 7110:110:7995:995 -H `zmhostname`
Now, to have all the mailbox servers use the proxy, simply set the zimbraMailReferMode to reverse-proxied on each mailbox server and restart mailboxd to have all the traffic go through the proxy. Do a 'zmcontrol restart' on this node and you should be up and running.
Simple Command With Defaults
The zmproxyconfig command can be run with limited arguments if the command defaults are acceptable. Run /opt/zimbra/libexec/zmproxyconfig to view all the argument options and the usage
Protocol Requirements Including HTTPS Redirect
HTTP proxy can support protocol modes for HTTP or HTTPS only, both HTTP and HTTPS, mixed HTTP and HTTPS or HTTPS redirect from HTTP. Redirect is a popular configuration. This configuration must be made to the proxy servers.
- HTTPS redirect from HTTP
zmprov ms proxy.server.name zimbraReverseProxyMailMode redirect
- HTTP and HTTPS (support both)
zmprov ms proxy.server.name zimbraReverseProxyMailMode both
- HTTPS only
zmprov ms proxy.server.name zimbraReverseProxyMailMode https
- HTTP only
zmprov ms proxy.server.name zimbraReverseProxyMailMode http
- "mixed" will cause only authentication to be sent over HTTPS
zmprov ms proxy.server.name zimbraReverseProxyMailMode mixed
Documents & Sharing
It is important to consider access to documents (Briefcase) and shares when setting up HTTP proxy. A publicly reachable address must be configured to be used for the REST and SOAP proxy interfaces otherwise components requiring access to these interfaces will fail. Calendar sharing is an example of one component. Set zimbraPublicServiceHostname, zimbraPublicServiceProtocol, and zimbraPublicServicePort when applicable. These values are usually not required without proxy since the REST and SOAP proxy interfaces take the value of the Zimbra mailbox service hostname by default. These attributes can be set globally to be inherited by all domains or per domain.
Set zimbraPublicServiceHostname to the value of the host that will be used in the URL for access to the HTTP proxy.
- This command sets mail.domain.com as the public hostname to be used for access to all domains in the Zimbra directory:
zmprov mcf zimbraPublicServiceHostname mail.domain.com
- This command sets mail.domaina.com as the public hostname to be used for access to domaina.com domain:
zmprov md domaina.com zimbraPublicServiceHostname mail.domaina.com
- Set zimbraPublicServiceProtocol to http or https depending on the protocol requirements for HTTP proxy:
zmprov md domaina.com zimbraPublicServiceProtocol https
- Set zimbraPublicServicePort to the value that corresponds to the HTTP proxy port used in the URL (optional if standard ports 80 or 443 are used for proxy listeners):
zmprov md domaina.com zimbraPublicServicePort 443
Proxy Login Slow
A common nginx misconfiguration is to have incorrectly designated non-mailbox servers as routing/zmlookup handlers. Only mailbox servers can perform route handler functions. To view the zmlookup lookup handlers, review the zm_lookup_handlers parameter in /opt/zimbra/conf/nginx/includes/nginx.conf.zmlookup
grep zm_lookup_handlers /opt/zimbra/conf/nginx/includes/nginx.conf.zmlookup
If a non-mailbox server is listed, set the zimbraReverseProxyLookupTarget server configuration attribute to FALSE for that server.
zmprov ms `zmhostname` zimbraReverseProxyLookupTarget FALSE
Additionally, zimbraReverseProxyLookupTarget is a server inherited attribute from the global configuration, so check if zimbraReverseProxyLookupTarget has been incorrectly designated in global config.
zmprov gcf zimbraReverseProxyLookupTarget
|Verified Against:||Date Created: 6/05/2014|
|Article ID: http://wiki.zimbra.com/index.php?title=Enabling_Zimbra_Proxy||Date Modified: 08/4/2014|